Hey if this drawing is useful consider hitting the upload button. (I fixed it 9/3/26. If you tried before then and it didn't work then try again.) Help someone else out by uploading sinks we don't already have. Or if we already have it that's okay, too. Upload your whole filesystem if you want.
If you use LPI's LT-2D3D with the original LT1 software and you're spending half the week deleting dimensions and setting layers then check out Weaselware. It will be
a full blown CAD editor when I'm done with it. Next up is auto placing texts, breaking and pulling
apart at the joints, and making oversized pieces automatically.
%%UNOTES:
1. ALL DIMENSIONS INSIDE RECTANGLES ARE CRITICAL
AND MUST BE HELD WITHIN PLUS OR MINUS .060" (1.5mm).
ANALYZE FOR SAFETY, ECOLOGY, AND MINIMUM ESSENTIAL DESIGN
LAST
REV
FD411714
MDPL
162726
ASSY
JEFF HARRIS
6" = 1'-0"
JEFF HARRIS
M.VAIL
FD411714
ALL DIMENSIONS ARE IN INCHES, UNLESS NOTED.
36
0
0
850 KITCHEN SINK
THIS DRAWING HAS BEEN FURNISHED BY E. I. DU PONT DE NEMOURS & CO.
THE INFORMATION AND KNOW-HOW THEREON MAY NOT BE USED NOR THE DRAWING
REPRODUCED WITHOUT THE WRITTEN PERMISSION OF DU PONT. ALL
REPRODUCTIONS IN WHOLE OR IN PART, INCLUDING VENDOR'S SHOP DRAWINGS,
SHALL BEAR OR REFER TO THIS STAMP.
E. I. DU PONT DE NEMOURS & CO., INC.
YERKES PLANT - BUFFALO, N.Y.
YERKES ENGINEERING ORGANIZATION
CCMC BLDG-300
YERKES PLANT
4.54"
115.38mm
10%%d
R
.03"
.81mm
17%%d
10%%d
R
.25"
6.32mm
.09"
2.2mm
.562"
14.28mm
R
.09"
2.35mm
3.56"
90.4mm
4.94"
125.49mm
16.69"
423.93mm
.75"
19.05mm
15%%d
7%%d
.50"
12.7mm
.50"
12.7mm
R
.25"
6.35mm
.50"
12.7mm
9.56"
242.82mm
3.56"
90.4mm
4.94"
125.49mm
9.0"
228.54mm
4.94"
125.49mm
3.56"
90.4mm
9.0"
228.54mm
9.56"
242.82mm
13.799"
350.49mm
1.402"
35.62mm
13.799"
350.49mm
.923"
23.45mm
16.690"
423.93mm
.936"
23.79mm
10.36"
263.15mm
10.13"
257.2mm
30.847"
783.51mm
5.25"
133.39mm
18.563"
471.5mm
Warning! Zero ratings!Total Downloads = 0
UserRatingComment
Vote remake if it caused / would cause a remake or if the drawing is just bad. Vote good enough if
you cut it, they installed it, and you never heard about it again or you checked it enough to
make sure it's okay.
Vote perfect if you checked the overhang all around and it's consistent and the curves are smooth
and
it's exactly what it's supposed to be.
N-NOT A SINK1-REMAKE2-GOOD ENOUGH3-PERFECTX-COMMENT ONLY
If you don't know the answer come back and vote later. Hit the rate button at the top of the
screen. Your downloads are stored there.
Top notch comments are 1/4" overhang, 5/16" overhang, sloppy overhang, flush cut, flush to bevel
at the top of the sink, accessories fit / don't fit, flush left to right with reveal top and bottom.
Anything that tells someone without the physical sink what they need to know.
Vote not a sink if it's a cooktop, faucet hole, empty file,
drawing of a dinosaur, whatever.
If a drawing gets 3 or more N votes and has an average rating under 1.0 then it
gets voted off the site.
This sink is from a legacy folder. It has not been ran through the DXF processor.