Hey if this drawing is useful consider hitting the upload button. (I fixed it 9/3/26. If you tried before then and it didn't work then try again.) Help someone else out by uploading sinks we don't already have. Or if we already have it that's okay, too. Upload your whole filesystem if you want.
If you use LPI's LT-2D3D with the original LT1 software and you're spending half the week deleting dimensions and setting layers then check out Weaselware. It will be
a full blown CAD editor when I'm done with it. Next up is auto placing texts, breaking and pulling
apart at the joints, and making oversized pieces automatically.
THIS DRAWING HAS BEEN FURNISHED BY E.I. DU PONT DE
MAY NOT BE USED NOR THE DRAWING REPRODUCED WITHOUT
WHOLE OR IN PART, INCLUDING VENDOR'S SHOP DRAWINGS,
SHALL BEAR OR REFER TO THIS STAMP.
THE WRITTEN PERMISSION OF DU PONT. ALL REPRODUCTIONS IN
NEMOURS & CO. THE INFORMATION AND KNOW-HOW THEREON
PROJECT
SCALE
DRAWN
CHECKED
DATE
E.I.DU PONT DE NEMOURS & CO.,INC.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
PROJ
NO
REVISION
RVSD
CHKD
APPD
DATE
PROJ
NO
REVISION
RVSD
CHKD
APPD
DATE
PROJ
NO
REVISION
RVSD
CHKD
APPD
DATE
PROJ
NO
REVISION
RVSD
CHKD
APPD
DATE
ANALYZE FOR SAFETY,ECOLOGY,AND MINIMUM ESSENTIAL DESIGN
AND MUST BE HELD WITHIN PLUS OR MINUS .060" (1.5mm).
%%UNOTES:
{ OF DRAIN
{
OF DRAIN
{ OF DRAIN
{ OF DRAIN
%%USECTION Z-Z
%%USECTION Y-Y
%%UDETAIL B
.06"
1.6mm
.39"
9.91mm
.50"
12.68mm
3.56"
90.4mm
7%%d
8.44"
214.39mm
.44"
11.18mm
9.0"
228.68mm
4.92"
124.97mm
10%%d
%%UDRAIN DETAIL
R
.03"
.8mm
R
.25"
6.3mm
R
.13"
3.2mm
10%%d
3.56"
90.4mm
4.92"
124.97mm
15%%d
4.57"
116.08mm
.75"
19.05mm
.44"
11.18mm
CARPENTER MARK
TYP.(4) PLACES
R
.02"
.5mm
.562"
14.29mm
R
.31"
7.9mm
.75"
19.05mm
%%USECTION X-X
CARPENTER MARK
FLANGE
R
.02"
.5mm
R
.31"
7.9mm
.44"
11.2mm
X
X
9.326"
236.9mm
18.651"
473.7mm
14.427"
366.45mm
28.854"
732.9mm
27.35"
694.8mm
.75"
19.1mm
17.15"
435.6mm
.75"
19.1mm
Warning! Zero ratings!Total Downloads = 0
UserRatingComment
Vote remake if it caused / would cause a remake or if the drawing is just bad. Vote good enough if
you cut it, they installed it, and you never heard about it again or you checked it enough to
make sure it's okay.
Vote perfect if you checked the overhang all around and it's consistent and the curves are smooth
and
it's exactly what it's supposed to be.
N-NOT A SINK1-REMAKE2-GOOD ENOUGH3-PERFECTX-COMMENT ONLY
If you don't know the answer come back and vote later. Hit the rate button at the top of the
screen. Your downloads are stored there.
Top notch comments are 1/4" overhang, 5/16" overhang, sloppy overhang, flush cut, flush to bevel
at the top of the sink, accessories fit / don't fit, flush left to right with reveal top and bottom.
Anything that tells someone without the physical sink what they need to know.
Vote not a sink if it's a cooktop, faucet hole, empty file,
drawing of a dinosaur, whatever.
If a drawing gets 3 or more N votes and has an average rating under 1.0 then it
gets voted off the site.
This sink is from a legacy folder. It has not been ran through the DXF processor.