Hey if this drawing is useful consider hitting the upload button. (I fixed it 9/3/26. If you tried before then and it didn't work then try again.) Help someone else out by uploading sinks we don't already have. Or if we already have it that's okay, too. Upload your whole filesystem if you want.
If you use LPI's LT-2D3D with the original LT1 software and you're spending half the week deleting dimensions and setting layers then check out Weaselware. It will be
a full blown CAD editor when I'm done with it. Next up is auto placing texts, breaking and pulling
apart at the joints, and making oversized pieces automatically.
ANALYZE FOR SAFETY, ECOLOGY, AND MINIMUM ESSENTIAL DESIGN
LAST
REV
FD411545
JEFF HARRIS
6" = 1'-0"
JEFF HARRIS
MARC VAIL
FD411545
ALL DIMENSIONS ARE IN INCHES, UNLESS NOTED.
36
8
901 A/S KITCHEN SINK
THIS DRAWING HAS BEEN FURNISHED BY E. I. DU PONT DE NEMOURS & CO.
THE INFORMATION AND KNOW-HOW THEREON MAY NOT BE USED NOR THE DRAWING
REPRODUCED WITHOUT THE WRITTEN PERMISSION OF DU PONT. ALL
REPRODUCTIONS IN WHOLE OR IN PART, INCLUDING VENDOR'S SHOP DRAWINGS,
SHALL BEAR OR REFER TO THIS STAMP.
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
DWG. NO.
LEVEL
REV.
DESCRIPTION
LEVEL
REV.
DESCRIPTION
DWG. NO.
E. I. DU PONT DE NEMOURS & CO., INC.
YERKES PLANT - BUFFALO, N.Y.
YERKES ENGINEERING ORGANIZATION
%%UDETAIL A
NOTES:
1. ALL DIMENSIONS INSIDE RECTANGLES ARE CRITICAL AND
MUST BE HELD WITHIN PLUS OR MINUS .060" (1.5mm).
2. SURFACE FINISH TO BE BASED ON SCOTCHBRITE
RED PAD ORBITAL FINISH.
%%USECTION B-B
TYP.
TYP.
R
.33"
8.38mm
%%USECTION A-A
SEE DETAIL A
.09"
2.23mm
.58"
14.75mm
5.06"
128.55mm
3.60"
91.33mm
10%%d
R
.09"
2.36mm
R
.25"
6.35mm
R
.04"
1.05mm
10%%d
4.56"
115.71mm
10%%d
438.35mm
.38"
9.65mm
10.39"
263.8mm
15%%d
7%%d
9.80"
249.02mm
.50"
12.7mm
3.60"
91.33mm
5.06"
128.52mm
.50"
12.7mm
%%USECTION C-C
OVERFLOW SLOT
EUROPEAN SINKS ONLY
.1"
3mm
.1"
3mm
+
+
-
-
1.25"
31.75mm
.875"
22.23mm
1.75"
44.45mm
.375"
9.53mm
B
B
%%UPLAN VIEW
C
C
17.258"
21.976"
558.19mm
19.260"
489.2mm
12.79"
324.99mm
11.97"
304.09mm
23.944"
608.18mm
Warning! Zero ratings!Total Downloads = 0
UserRatingComment
Vote remake if it caused / would cause a remake or if the drawing is just bad. Vote good enough if
you cut it, they installed it, and you never heard about it again or you checked it enough to
make sure it's okay.
Vote perfect if you checked the overhang all around and it's consistent and the curves are smooth
and
it's exactly what it's supposed to be.
N-NOT A SINK1-REMAKE2-GOOD ENOUGH3-PERFECTX-COMMENT ONLY
If you don't know the answer come back and vote later. Hit the rate button at the top of the
screen. Your downloads are stored there.
Top notch comments are 1/4" overhang, 5/16" overhang, sloppy overhang, flush cut, flush to bevel
at the top of the sink, accessories fit / don't fit, flush left to right with reveal top and bottom.
Anything that tells someone without the physical sink what they need to know.
Vote not a sink if it's a cooktop, faucet hole, empty file,
drawing of a dinosaur, whatever.
If a drawing gets 3 or more N votes and has an average rating under 1.0 then it
gets voted off the site.
This sink is from a legacy folder. It has not been ran through the DXF processor.